DIY Virtuix Omni
-
- One Eyed Hopeful
- Posts: 40
- Joined: Wed Sep 19, 2012 8:24 am
DIY Virtuix Omni
Has anyone thought about taking a few of these plastic vert ramps, they have different sizes and they are about 20$ a piece. I could see cutting these into triangles and fixing them together. I have attached a link below to one that I was using as an example.
http://www.amazon.com/Razor-13430-Punk- ... d_sim_sg_4
Adding to the idea I could see using spray foam under the botton to give it more support, might be a better option but thats the first thing that comes to mind.
http://www.amazon.com/Razor-13430-Punk- ... d_sim_sg_4
Adding to the idea I could see using spray foam under the botton to give it more support, might be a better option but thats the first thing that comes to mind.
- colocolo
- Diamond Eyed Freakazoid!
- Posts: 790
- Joined: Mon Jun 04, 2012 1:25 am
Re: DIY Virtuix Omni
it would be cheaper and better if you cast a curved dish with concrete.
Make a wooden curvature stencil and draw/pull the curved negative form(like a pair of compasses) into claylike earth.
Then add the concrete and cover the whole thing up.
After it has set hard cover it with some low friction(teflon) foliage.
Make a wooden curvature stencil and draw/pull the curved negative form(like a pair of compasses) into claylike earth.
Then add the concrete and cover the whole thing up.
After it has set hard cover it with some low friction(teflon) foliage.
Last edited by colocolo on Wed Jun 05, 2013 8:01 am, edited 1 time in total.
-
- One Eyed Hopeful
- Posts: 40
- Joined: Wed Sep 19, 2012 8:24 am
Re: DIY Virtuix Omni
Are you suggesting that concrete would be a good replacement or that it would be used to create a mold? 1. How would you move that 2. whose wife would allow that in the house?
- museumsteve
- Binocular Vision CONFIRMED!
- Posts: 201
- Joined: Tue Mar 26, 2013 5:29 am
Re: DIY Virtuix Omni
lol..I was looking at these ramps online yesterday
I'm thinking I fancy making something myself, not just because the cost of Omni with shipping.VAT to UK but because if I wanted something I wouldn't want another 9-12 month wait.
I'm thinking I fancy making something myself, not just because the cost of Omni with shipping.VAT to UK but because if I wanted something I wouldn't want another 9-12 month wait.
-
- One Eyed Hopeful
- Posts: 40
- Joined: Wed Sep 19, 2012 8:24 am
- colocolo
- Diamond Eyed Freakazoid!
- Posts: 790
- Joined: Mon Jun 04, 2012 1:25 am
Re: DIY Virtuix Omni
No, you make the mold out of claylike earth or clay. The omni weighs 50 Kilos. The concrete dish wouldShannonb1 wrote:Are you suggesting that concrete would be a good replacement or that it would be used to create a mold? 1. How would you move that 2. whose wife would allow that in the house?
weigh much more. Better you would leave it in the garden.
Now, this wife thing in general is making me sick.
EDIT: Perhaps in the future ODTs will be intergrated into the floor when the house is going to be build.
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
I'm considering this now that I have the harness set up.
One possibility might be to get a floor mat like this:
http://www.ikea.com/ca/en/catalog/products/44881100/
And then cut it / warm it so it molds into a dish shape. Need a circular frame, however.
One possibility might be to get a floor mat like this:
http://www.ikea.com/ca/en/catalog/products/44881100/
And then cut it / warm it so it molds into a dish shape. Need a circular frame, however.
Gear VR: Maybe OVR isn't so evil after all!
-
- Petrif-Eyed
- Posts: 2708
- Joined: Sat Sep 01, 2012 10:47 pm
Re: DIY Virtuix Omni
Just don't substitute hydrogen peroxide for that styrofoam, eh?Shannonb1 wrote:More info on making plastic as a consumer
http://www.instructables.com/id/How-to- ... 2-plastic/
This work is licensed under a Creative Commons Attribution-ShareAlike 3.0 Unported License.
- OutatimeTV
- One Eyed Hopeful
- Posts: 41
- Joined: Wed Mar 20, 2013 5:00 pm
- Location: Germany
Re: DIY Virtuix Omni
When I was looking for an DIY Omni dish, I came across these 120cm metal firebowls for outside use.
But I am not sure how well you can walk in such things.
But I am not sure how well you can walk in such things.
- mickman
- Binocular Vision CONFIRMED!
- Posts: 279
- Joined: Mon Jun 04, 2012 5:07 pm
- Location: London
- Contact:
Re: DIY Virtuix Omni
A simple 2 part mould that can easily be 3D Printed.
I think it won't be long and we'll be seeing omni moulds at Thingiverse.
Clip the pieces together and hey presto you got yourself an Omni V2.
Or perhaps 3D print the mould & then vacuum form each part...
Simple to Replicate ... I think many people were unaware exactly what secret weapon was under the shoe... now we know... Here come the Clones .. Sad but True
Not sure if it's a good thing or a bad thing.... but one thing I am sure about is JanVR's Omni scooped up on KickStarter & he'll be grinning from ear to ear at any new variations that hit the streets
I think it won't be long and we'll be seeing omni moulds at Thingiverse.
Clip the pieces together and hey presto you got yourself an Omni V2.
Or perhaps 3D print the mould & then vacuum form each part...
Simple to Replicate ... I think many people were unaware exactly what secret weapon was under the shoe... now we know... Here come the Clones .. Sad but True
Not sure if it's a good thing or a bad thing.... but one thing I am sure about is JanVR's Omni scooped up on KickStarter & he'll be grinning from ear to ear at any new variations that hit the streets
Last edited by mickman on Thu Jun 06, 2013 9:35 am, edited 1 time in total.
- FingerFlinger
- Sharp Eyed Eagle!
- Posts: 429
- Joined: Tue Feb 21, 2012 11:57 pm
- Location: Irvine, CA
Re: DIY Virtuix Omni
That would be pretty large for a consumer-level 3D printer, no?
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
Yeah, I thought through the 3d printer thing. If you get a very large printing platform, you could probably build it in parts. About 25-50 of them. Need to make sure they all fit together snugly. Each part would likely take several hours. So, we're talking about something that would take about 10 days of printing straight. Likely you'd be able to get about 12 hours a day, so make that 20 days of printing. More than likely, your printer would probably die several times on a job like that (3d printers are notoriously unreliable).
It'd be a big job, but doable perhaps if you're patient enough.
It'd be a big job, but doable perhaps if you're patient enough.
Gear VR: Maybe OVR isn't so evil after all!
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
One possible approach might be to glue / nail three+ layers of MDF together with concentric circles cut out. And then sand, smooth them until you have something reasonable.
For bonus points, fill it with large ball bearings.
Need to figure out a better approach than Jan's for stopping all that sliding around the place though.
One possibility might be some kind of surface on the shoes and dish which is very high friction for lateral movement but not forward/back movement.
For bonus points, fill it with large ball bearings.
Need to figure out a better approach than Jan's for stopping all that sliding around the place though.
One possibility might be some kind of surface on the shoes and dish which is very high friction for lateral movement but not forward/back movement.
Last edited by blazespinnaker on Thu Jun 06, 2013 8:36 am, edited 1 time in total.
Gear VR: Maybe OVR isn't so evil after all!
- TheHolyChicken
- Diamond Eyed Freakazoid!
- Posts: 733
- Joined: Thu Oct 18, 2012 3:34 am
- Location: Brighton, UK
- Contact:
Re: DIY Virtuix Omni
Sounds like it would take less time and effort to just go work evenings for a while and use the extra cash to simply buy an Omni, haha.
Sometimes I sits and thinks, and sometimes I just sits.
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
Great contribution! Thanks!TheHolyChicken wrote:Sounds like it would take less time and effort to just go work evenings for a while and use the extra cash to simply buy an Omni, haha.
Gear VR: Maybe OVR isn't so evil after all!
- colocolo
- Diamond Eyed Freakazoid!
- Posts: 790
- Joined: Mon Jun 04, 2012 1:25 am
Re: DIY Virtuix Omni
Place a strong electromagnet beneath the center surface that would attract the part metalic sole.blazespinnaker wrote:One possible approach might be to glue / nail three+ layers of MDF together with concentric circles cut out. And then sand, smooth them until you have something reasonable.
For bonus points, fill it with large ball bearings.
Need to figure out a better approach than Jan's for stopping all that sliding around the place though.
One possibility might be some kind of surface on the shoes and dish which is very high friction for lateral movement but not forward/back movement.
I am wondering if it would be possible to build a ODT with several linear motors pointing towards the center.
The linear motors would let your shoe, which is the actual counter part, glide back towards the center.
a bit like a floating MAGLEV although your shoe would more glide over a low friction surface.
The dish would not need to be curved anymore also.
- TheHolyChicken
- Diamond Eyed Freakazoid!
- Posts: 733
- Joined: Thu Oct 18, 2012 3:34 am
- Location: Brighton, UK
- Contact:
Re: DIY Virtuix Omni
The irony of your retort is palpable.blazespinnaker wrote:Great contribution! Thanks!TheHolyChicken wrote:Sounds like it would take less time and effort to just go work evenings for a while and use the extra cash to simply buy an Omni, haha.
Sometimes I sits and thinks, and sometimes I just sits.
-
- Cross Eyed!
- Posts: 105
- Joined: Wed Sep 22, 2010 3:47 am
- Location: Toulouse, France
Re: DIY Virtuix Omni
something like a roller skate on a standard surface ?blazespinnaker wrote: One possibility might be some kind of surface on the shoes and dish which is very high friction for lateral movement but not forward/back movement.
-
- Petrif-Eyed
- Posts: 2708
- Joined: Sat Sep 01, 2012 10:47 pm
Re: DIY Virtuix Omni
Lay an old BUD satellite dish on the ground and roller skate on it?
http://www.youtube.com/watch?v=rCOvBd2HZss
Something like this, but smaller, and while wearing a Rift:
http://www.youtube.com/watch?v=Evz0F2_c3Mg
http://www.youtube.com/watch?v=rCOvBd2HZss
Something like this, but smaller, and while wearing a Rift:
http://www.youtube.com/watch?v=Evz0F2_c3Mg
This work is licensed under a Creative Commons Attribution-ShareAlike 3.0 Unported License.
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
The problem with roller skates is that they don't stop rolling.
You need something that you can stand up straight with maximum stability.
One thing I came up with last night was a concave dish with manual treadmills pointing upwards and outwards at different angles. So instead of sliding, your feet would actually move like on a treadmill. Expensive and tricky though. Too many moving parts.
You need something that you can stand up straight with maximum stability.
One thing I came up with last night was a concave dish with manual treadmills pointing upwards and outwards at different angles. So instead of sliding, your feet would actually move like on a treadmill. Expensive and tricky though. Too many moving parts.
Gear VR: Maybe OVR isn't so evil after all!
- colocolo
- Diamond Eyed Freakazoid!
- Posts: 790
- Joined: Mon Jun 04, 2012 1:25 am
Re: DIY Virtuix Omni
or, sth like this .with the only difference that the role band would be inclined and your foot would glide back.blazespinnaker wrote:The problem with roller skates is that they don't stop rolling.
You need something that you can stand up straight with maximum stability.
One thing I came up with last night was a concave dish with manual treadmills pointing upwards and outwards at different angles. So instead of sliding, your feet would actually move like on a treadmill. Expensive and tricky though. Too many moving parts.
you could even tune the roll resistance.
You do not have the required permissions to view the files attached to this post.
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
Yeah, that looks interesting. Maybe some kind of motorized levers to move each triangle up and down depending on the incline.
Gear VR: Maybe OVR isn't so evil after all!
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
Gear VR: Maybe OVR isn't so evil after all!
- colocolo
- Diamond Eyed Freakazoid!
- Posts: 790
- Joined: Mon Jun 04, 2012 1:25 am
Re: DIY Virtuix Omni
yes, or to control the gait.blazespinnaker wrote:Yeah, that looks interesting. Maybe some kind of motorized levers to move each triangle up and down depending on the incline.
What if you put in the middle of the center a round post at which you mount this bungee rope.
each time you walk onto the rolls your one foot glides back. the rope could turn 360°.
i think that would work.
Perhaps.
- colocolo
- Diamond Eyed Freakazoid!
- Posts: 790
- Joined: Mon Jun 04, 2012 1:25 am
Re: DIY Virtuix Omni
a slippery flat surface around a high friction center would be enough i guess.
the only problem i see is when you put one foot onto the slippery surface and put weight onto it you would be immediately pulled back. Perhaps one only has to find a good friction value.
the only problem i see is when you put one foot onto the slippery surface and put weight onto it you would be immediately pulled back. Perhaps one only has to find a good friction value.
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
Here's my current idea, basically 3 or 4 MDF boards nailed/glued together with circles cut out, and then I'll lower a plastic carpet cover over it which I'll soften with heat.
I'll do a bit of sanding, but not too crazy.
Any folds that develop will be fine as they should restrict lateral movement.
I'll do a bit of sanding, but not too crazy.
Any folds that develop will be fine as they should restrict lateral movement.
You do not have the required permissions to view the files attached to this post.
Gear VR: Maybe OVR isn't so evil after all!
- colocolo
- Diamond Eyed Freakazoid!
- Posts: 790
- Joined: Mon Jun 04, 2012 1:25 am
Re: DIY Virtuix Omni
but how would your foot glide off the steps?
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
The plastic cover is very low friction. I'll just wear socks.
I'll sand the steps a bit, just to get rid of the major edges, but I'll rely on the plastic cover to create a smooth transition.
It's a pretty thick plastic cover, btw.
http://www.ikea.com/ca/en/catalog/products/44881100/
I'll sand the steps a bit, just to get rid of the major edges, but I'll rely on the plastic cover to create a smooth transition.
It's a pretty thick plastic cover, btw.
http://www.ikea.com/ca/en/catalog/products/44881100/
Gear VR: Maybe OVR isn't so evil after all!
-
- Cross Eyed!
- Posts: 141
- Joined: Thu Sep 02, 2010 3:08 pm
Re: DIY Virtuix Omni
Plastic layer has to be thin enough that with heat, you can mold it to the right shape.
Or you will have to cut shapes, and re attach it.
One flat square will not mold to a dome easily without buckling.
How about finding a lid to a really big trash can or something? If you get something the right shape (or almost) you might be able to use expansion foam and a bit of framing to fill the bits.
Or you will have to cut shapes, and re attach it.
One flat square will not mold to a dome easily without buckling.
How about finding a lid to a really big trash can or something? If you get something the right shape (or almost) you might be able to use expansion foam and a bit of framing to fill the bits.
- Okta
- Golden Eyed Wiseman! (or woman!)
- Posts: 1515
- Joined: Tue Feb 12, 2008 5:22 am
Re: DIY Virtuix Omni
There is a young gentleman in another thread who is way ahead of the pack http://www.mtbs3d.com/phpBB/viewtopic.php?f=120&t=17269
If I DIY it will be similar to this.
If I DIY it will be similar to this.
"I did not chip in ten grand to seed a first investment round to build value for a Facebook acquisition."
Notch on the FaceDisgrace buyout.
Notch on the FaceDisgrace buyout.
- mickman
- Binocular Vision CONFIRMED!
- Posts: 279
- Joined: Mon Jun 04, 2012 5:07 pm
- Location: London
- Contact:
Re: DIY Virtuix Omni
Looks like good ole wood and nails is the way forwards.
As high-tech as V.R is...... there's still room for good ole wood.
Me thinks its time to get out the rusty axe & chop me up a good ole holodeck.
As high-tech as V.R is...... there's still room for good ole wood.
Me thinks its time to get out the rusty axe & chop me up a good ole holodeck.
- MrGreen
- Diamond Eyed Freakazoid!
- Posts: 741
- Joined: Mon Sep 03, 2012 1:36 pm
- Location: QC, Canada
Re: DIY Virtuix Omni
By far the best idea I've read in this thread though.blazespinnaker wrote:Great contribution! Thanks!TheHolyChicken wrote:Sounds like it would take less time and effort to just go work evenings for a while and use the extra cash to simply buy an Omni, haha.
-
- One Eyed Hopeful
- Posts: 40
- Joined: Wed Sep 19, 2012 8:24 am
Re: DIY Virtuix Omni
And no, not a great contributionMrGreen wrote:By far the best idea I've read in this thread though.blazespinnaker wrote:Great contribution! Thanks!TheHolyChicken wrote:Sounds like it would take less time and effort to just go work evenings for a while and use the extra cash to simply buy an Omni, haha.
I think you all are missing the point. I can build something to work with in a weekend....you guys are talking about waiting till at least JANUARY of 2014, so if you don't have something productive to say as far as ideas, post your trolling somewhere else. Its not about money, its about time. I have plenty of money which is why I can build one now and buy one if its really better later.
I'm rather serious about this topic and looking for others who are as well to contribute to the idea.
-
- Two Eyed Hopeful
- Posts: 71
- Joined: Sun May 30, 2010 3:55 am
Re: DIY Virtuix Omni
This is cool, but what about using some wood filler or similar with a filling knife to smooth over the transitions from one layer to the next? You could make a reasonable DIY ramp like that. Any imperfections will be covered by the next layer, ie carpet. Only problem I can see if whether it'll stand up to being run on, or whether it would crack and fall apart? If you're gluing the carpet layer on then that may well hold it in place anyway. I think there must be a decent way of doing this.blazespinnaker wrote:Here's my current idea, basically 3 or 4 MDF boards nailed/glued together with circles cut out, and then I'll lower a plastic carpet cover over it which I'll soften with heat.
I'll do a bit of sanding, but not too crazy.
Any folds that develop will be fine as they should restrict lateral movement.
Something that just came to mind while typing, how about cutting the edges using a circular saw at a 45 degree angle? Then you'd have quite a nice ramp that wouldn't fall apart. Wouldn't need to be perfect and the next layer will cover it.
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
It depends on how much heat you apply. Plastic is very moldable when you warm it up enough.Lilwolf wrote:Plastic layer has to be thin enough that with heat, you can mold it to the right shape.
Or you will have to cut shapes, and re attach it.
One flat square will not mold to a dome easily without buckling.
How about finding a lid to a really big trash can or something? If you get something the right shape (or almost) you might be able to use expansion foam and a bit of framing to fill the bits.
I was planning on sanding/smoothing the edges down with a belt sander. Wood filler is an interesting idea though. Thanks for the tip.This is cool, but what about using some wood filler or similar with a filling knife to smooth over the transitions from one layer to the next? You could make a reasonable DIY ramp like that. Any imperfections will be covered by the next layer, ie carpet. Only problem I can see if whether it'll stand up to being run on, or whether it would crack and fall apart? If you're gluing the carpet layer on then that may well hold it in place anyway. I think there must be a decent way of doing this.
Something that just came to mind while typing, how about cutting the edges using a circular saw at a 45 degree angle? Then you'd have quite a nice ramp that wouldn't fall apart. Wouldn't need to be perfect and the next layer will cover it.
Another possibility is a thin layer of tile mortar.
Gear VR: Maybe OVR isn't so evil after all!
-
- Two Eyed Hopeful
- Posts: 71
- Joined: Sun May 30, 2010 3:55 am
Re: DIY Virtuix Omni
Yeah, there are probably lots of DIY products that could do it. Do you not like the circular saw idea? I thought that would be much betteR?blazespinnaker wrote:It depends on how much heat you apply. Plastic is very moldable when you warm it up enough.Lilwolf wrote:Plastic layer has to be thin enough that with heat, you can mold it to the right shape.
Or you will have to cut shapes, and re attach it.
One flat square will not mold to a dome easily without buckling.
How about finding a lid to a really big trash can or something? If you get something the right shape (or almost) you might be able to use expansion foam and a bit of framing to fill the bits.
I was planning on sanding/smoothing the edges down with a belt sander. Wood filler is an interesting idea though. Thanks for the tip.This is cool, but what about using some wood filler or similar with a filling knife to smooth over the transitions from one layer to the next? You could make a reasonable DIY ramp like that. Any imperfections will be covered by the next layer, ie carpet. Only problem I can see if whether it'll stand up to being run on, or whether it would crack and fall apart? If you're gluing the carpet layer on then that may well hold it in place anyway. I think there must be a decent way of doing this.
Something that just came to mind while typing, how about cutting the edges using a circular saw at a 45 degree angle? Then you'd have quite a nice ramp that wouldn't fall apart. Wouldn't need to be perfect and the next layer will cover it.
Another possibility is a thin layer of tile mortar.
- blazespinnaker
- Certif-Eyed!
- Posts: 541
- Joined: Sat Sep 01, 2012 11:53 pm
Re: DIY Virtuix Omni
It's not a bad idea, should save a bit of time, though sometimes tricky to cut that way.
My belt sander is pretty powerful though and this is MDF we're talking about.
Another idea on the other thread is to use cut pieces of laminate. I think I'll go that route instead of the plastic cover.
My belt sander is pretty powerful though and this is MDF we're talking about.
Another idea on the other thread is to use cut pieces of laminate. I think I'll go that route instead of the plastic cover.
Gear VR: Maybe OVR isn't so evil after all!
- colocolo
- Diamond Eyed Freakazoid!
- Posts: 790
- Joined: Mon Jun 04, 2012 1:25 am
Re: DIY Virtuix Omni
Today, i had another idea about a ODT.
Mainly like the Omni, but flat and no grooves.
Your shoes would have cleats like football shoes that can extrude out if no pressure is applied.
So, if your shoe glides over the low friction surface the low friction cleats retract and would glide backwards until they drift over the center of the device. There the platform has many holes like a grid. The pins extrude out and give you halt when stepping again forward.
I had this idea also with steel pins that would be attracted by a electromagnetic shoe sole, but think
this way its much simpler.
I think retractable cleats at the shoes and small holes in the center of the Omni could eventually improve it.
Mainly like the Omni, but flat and no grooves.
Your shoes would have cleats like football shoes that can extrude out if no pressure is applied.
So, if your shoe glides over the low friction surface the low friction cleats retract and would glide backwards until they drift over the center of the device. There the platform has many holes like a grid. The pins extrude out and give you halt when stepping again forward.
I had this idea also with steel pins that would be attracted by a electromagnetic shoe sole, but think
this way its much simpler.
I think retractable cleats at the shoes and small holes in the center of the Omni could eventually improve it.
-
- Two Eyed Hopeful
- Posts: 71
- Joined: Sun May 30, 2010 3:55 am
Re: DIY Virtuix Omni
How about doing it like you say then putting a layer of hardboard over it? You could even wet it to get it to take the shape better?
- mickman
- Binocular Vision CONFIRMED!
- Posts: 279
- Joined: Mon Jun 04, 2012 5:07 pm
- Location: London
- Contact:
Re: DIY Virtuix Omni
So i started my creation...
here's a quick pre-vis image.
Dish Skirting: The inset box holes beneath the dish will house LEDs ( gotta have a bit o bling )
If I add grooves to the dish I will have slits in each groove... so the light will fliter through and around the dish.
Stowage: I'll upload an animation shortly depicting how it will stow away. Basically each arms pivots from the base.. as they rotate inwards the attached spring cord will allow the ring to lower until it rests on the dish itself...
This system will allow the user to simply walk onto the dish.. push a button, the ring then lifts automatically up around them as the support bars fold outwards.
Regarding the Original Omni - I believe by Jan.2014 there'll be so many adaptations of the Omni that the original will be obsolete.
here's a quick pre-vis image.
Dish Skirting: The inset box holes beneath the dish will house LEDs ( gotta have a bit o bling )
If I add grooves to the dish I will have slits in each groove... so the light will fliter through and around the dish.
Stowage: I'll upload an animation shortly depicting how it will stow away. Basically each arms pivots from the base.. as they rotate inwards the attached spring cord will allow the ring to lower until it rests on the dish itself...
This system will allow the user to simply walk onto the dish.. push a button, the ring then lifts automatically up around them as the support bars fold outwards.
Regarding the Original Omni - I believe by Jan.2014 there'll be so many adaptations of the Omni that the original will be obsolete.
Last edited by mickman on Fri Jun 07, 2013 2:39 pm, edited 4 times in total.